shopping cart empty
[dismiss] Kung Hei Fat Choy. FastTech will be on holiday from January 20, 2020, to January 31, 2020. Shipping and support will resume normal service on February 1, 2020. (details)
rmrfyou's Product Reviews
Sort:

rmrfyou
Member

VERIFIED OWNER
  • JoinedMar 2013
  • Posts 254
  • Reviews 35
  • Kudos41
Overall   (3.2)
› Quality
› Value
2 of 2 people found the following review helpful
PROS
Small, looks good
CONS
Flat top 18350 efest imr doesn't fit.. You need to sand down the 510 center pin or the top / bottom caps can't screw together tightly with most rbas
Button is pretty good spring is just right. Bottom contact is the cyc style and the top contact is like a the bottom of a screw. Unfortunately its too long and my fogger on top sitting flush i am unable to screw the top cap or bottom cap together tightly. Im using the shortest batteries you can find efest 18359 flat tops unprotected red imrs. Also the top contact I'm unsure if it's silver plated looks like some silver paint. It doesn't matter because i need to sand off a mm so all pieces can screw together tightly. It looks nice though with the brass n ss pieces and i like the ss top hopefully the 510 threading is ss for longevity. i got #360. Its nice and light, short and stealthy. Put a aga dripper on it and you can take this outside the home. Even with the aga rda the pin is too long with it sitting flush.
Reviewed on Was this review helpful to you? Yes / No

rmrfyou
Member

VERIFIED OWNER
  • JoinedMar 2013
  • Posts 254
  • Reviews 35
  • Kudos41
Overall   (4.2)
› Quality
› Value
1 of 1 people found the following review helpful
PROS
Price, stainless steel
Great mod for the price. Stock spring makes the button hot, and the battery too. So change the spring and the mod would be perfect
Reviewed on Was this review helpful to you? Yes / No

rmrfyou
Member

VERIFIED OWNER
  • JoinedMar 2013
  • Posts 254
  • Reviews 35
  • Kudos41
Overall   (2.7)
› Quality
› Value
1 of 1 people found the following review helpful
CONS
Designed poorly, not airtight
I bought this when it was first released and it leaked and leaked juice out the airhole. In the discussion messages there was some who were able to stop the leaks using orings but that didn't work fur me. I sent it back thinking i got a bad one and received a 2nd one with the same problem. I tried every tip but i will can't get a airtight seal. i even bought a nano tank kit because someone said that fixes the issue but not for me.
Reviewed on Was this review helpful to you? Yes / No

rmrfyou
Member

VERIFIED OWNER
  • JoinedMar 2013
  • Posts 254
  • Reviews 35
  • Kudos41
Overall   (4.2)
› Quality
› Value
1 of 1 people found the following review helpful
PROS
Slightly shorter than kayfun 31
CONS
Not really any cons. I like it if it wasn't so long. You can eliminate a lot of length if they used a shorter drip tip and dt housing
Since i already got the initial kayfun 31 ft batch with plated positive post block this one id full ss. Build quality is really good. I did a quick wash didn't see much machining oil or dirty crap. Did a quick 2mm folded ekowool wick build and on first attempt got a great 1.2 ohm coil with 28g wire. Used tweezers and did a dry burn and immediately clamped the coils together to get them touching like a microcoil. Vapes great. No leaks, no flooding, clean taste. Draw is tight need to figure out how to open it up. I like both ft kayfuns and would recommend both and the fogger. You will probably never go back to using your genesis rbas. Even though this is slightly shorter than the 3.1 its still fairly long and looks funny on a 18350 mech. Again i think the manufacturers can shorten down the kfl by half inch if they used a shorter tip and drip tip housing.
Reviewed on Was this review helpful to you? Yes / No

rmrfyou
Member

VERIFIED OWNER
  • JoinedMar 2013
  • Posts 254
  • Reviews 35
  • Kudos41
Overall   (4.2)
› Quality
› Value
1 of 1 people found the following review helpful
PROS
Easy to build took me 2 tries for perfect coil and wicking. Many options of coil designs you can build.
CONS
Plated internals from initial batch but ft is resolving the situation. Plastic tank threading is that good. Some defects on it so it's not a clean look so i am using the metal tank instead.
Using 2mm braided ekowool folded wrapped 28g about 6 or 7 wraps for 1.4 ohms. First try i had flooding so i adjusted the wicks and fixed it. Nice vapor and clean vape. I love my fogger but haven't stopped vaping my kayfun yet. I did notice some rust color on the 3rd hole (furthest to right) on the bottom. Im not too clear if that's the fill port or the first hole with screw in it is the fill port. The positive post block shows some rusting on the hole on the side of the block. Again this is the initial batch not the the new one that ft claims will be full ss. I fill from the top no leaking no flooding i cover the airhole ( center hole) using my finger, fill juice course to top, place top cap on, flip the kayfun, let go of air hole, screw in top cap to create vacuum.
Reviewed on Was this review helpful to you? Yes / No