shopping cart empty
WORLDWIDE FREE SHIPPING

Dry hits! I'm sure mine has much smaller juice flow holes than on youtube reviews and google images!
Login to post a new topic and to write a reply.
Thread Tools Rate This Thread


Search within thread:

Login to rate this thread.
#1 (permalink)      1/13/2017 6:25:54 PM US Central   quote/reply + tips
SmokeyPete
Member
  • JoinedDec 2013
  • Posts 545
  • Reviews 10
  • Kudos100
Dry hits! I'm sure mine has much smaller juice flow holes than on youtube reviews and google images!
Has anyone else found this?
Rhubarb & Custard Crumble!
#2 (permalink)      1/13/2017 11:32:28 PM US Central   quote/reply + tips
Avatar
Wylie
Member
  • JoinedMay 2013
  • Posts 5310
  • Reviews 77
  • Kudos3462
Just ran mine dry a little while ago while watching a movie in TC mode on the 213 and it just ran out of vapor, no dry hits. If you're using anything thicker than 50/50 liquid that may be the problem.

Edited on 1/13/2017 at 11:34 PM. Reason:
Always keep your ear to the ground!
#3 (permalink)      1/18/2017 1:01:30 PM US Central   quote/reply + tips
aguag
Member
  • JoinedSep 2013
  • Posts 356
  • Reviews 70
  • Kudos193
I use high 80-100 vg not had any probs, build wick fill vape not missed a step, if you like to grumble bout shit don't buy this.
Negativity is a creature that breeds of it's own kind.
#4 (permalink)      1/18/2017 1:35:23 PM US Central   quote/reply + tips
BladeRunner108
Member
  • JoinedOct 2016
  • Posts 34
  • Reviews 0
  • Kudos23
took me a try to two to figure out the wicking, upgrading from a Griffin 22. But nah brah you jus gotta twist the airflow open and probably use less cotton. it MIGHT be the juice that you're using but I doubt it. And unless your channels are completely closed or you packed down that cotton over/through the holes (it's gotta be just lightly blocking them) i doubt it's because of a mechanical error.
#5 (permalink)      1/18/2017 1:45:13 PM US Central   quote/reply + tips
Avatar
Watercool
Member
  • JoinedDec 2013
  • Posts 10529
  • Reviews 307
  • Kudos8096
other reviewers complained about lack of clearance between the glass and the chamber. Thats why I did cancel my order right in time... hate such stuff...
#6 (permalink)      1/18/2017 8:20:08 PM US Central   quote/reply + tips
Avatar
Wylie
Member
  • JoinedMay 2013
  • Posts 5310
  • Reviews 77
  • Kudos3462

other reviewers complained about lack of clearance between the glass and the chamber. Thats why I did cancel my order right in time... hate such stuff...


Just after about 12:44

Always keep your ear to the ground!
#7 (permalink)      1/19/2017 2:00:52 AM US Central   quote/reply + tips
Avatar
yoshy262
Member
  • JoinedDec 2014
  • Posts 2758
  • Reviews 49
  • Kudos2932
This is bullshit.
If you don't know how to wick your tank then the tank is bad?

I am using mine with 80 VG - 20 water and I never got any dry hits or liquid leaks issues.
I got inside fused clapton coils or alien, at 0.15-0.20 and is ok.
The single issue with this is the flavor, not the best or not the worst, but that is another thing.

Tip - Try scottish roll method, after you cut the ends comb them with something pointy, after that check again if is the same experience.
Also after you comb the wick just cut it at the right length,
do not leave too much cotton, wick touch the base not fold at the bottom.
Coils - make them at 3 mm, is the best fit for this tank.




Edited on 1/19/2017 at 2:29 AM. Reason:
Look but don't touch. Touch, but don't taste. Taste, don't swallow.
#8 (permalink)      1/19/2017 3:05:11 AM US Central   quote/reply + tips
Avatar
Wylie
Member
  • JoinedMay 2013
  • Posts 5310
  • Reviews 77
  • Kudos3462
4mm I.D. 0.22 ohms with this wire and just refilled with 50/50 and no flooding.


Even more of a juice pig than it was!

Edit: the guy in that video's going to have a hot spot in his coil, take a good look at the spacing. Floods his air flow priming the wick too.

Edited on 1/19/2017 at 3:10 AM. Reason:
Always keep your ear to the ground!
#9 (permalink)      1/19/2017 7:02:48 AM US Central   quote/reply + tips
Avatar
Wylie
Member
  • JoinedMay 2013
  • Posts 5310
  • Reviews 77
  • Kudos3462
Along with polishing the exterior of the atomizing chamber the accumulated 30 minutes has proven to be well worth the effort. I'm running my wattage higher with a denser more flavorful vape so this would mean the Ammit does wick better after the mods.
Always keep your ear to the ground!
#10 (permalink)      2/9/2017 3:54:57 PM US Central   quote/reply + tips
Avatar
Taifix
Member
  • JoinedJan 2015
  • Posts 285
  • Reviews 104
  • Kudos142
+1 details


Drill the holes to 3,2mm and use a Dremel for the other stuff.
File down the outer chamber to half of the material thickness.
Put the outer chamber on a drill for this to make it thinner.
Air bubbles come up imediately now even with 30/70 and -8 degrees outside.
Cotton is wet like a virgin - tastes like a Dripper!

Edited on 2/9/2017 at 3:58 PM. Reason:
#11 (permalink)      2/9/2017 4:27:33 PM US Central   quote/reply + tips
Avatar
Watercool
Member
  • JoinedDec 2013
  • Posts 10529
  • Reviews 307
  • Kudos8096
+2 details
yoshy262 wrote:

This is bullshit.If you don't know how to wick your tank then the tank is bad?I am using mine with 80 VG - 20 water



20% water makes your juice like plain PG.. THIS is bullshit ;)

I am not talking about lack of wicking - seem like with the mage gta, the juice does not even make it to the juice holes. This has nothing to do with the cotton inside.


Edited on 2/9/2017 at 4:30 PM. Reason: