$332.95 Hantek DSO5102B USB Digital Storage Oscilloscope (US) - authentic / 2CH / 100MHz / 1GSa/s / 7" TFT display at FastTech

Features:

200 / 100 / 60MHz bandwidths
1GSa/s Real Time sample rate
Large (7.0-inch) color display,WVGA(800x480)
Record length up to 1M
Trigger mode : edge / pulse width / line selectable video / slop / overtime etc.
USB host and device connectivity, standard
Multiple automatic measurements
Four math functions, including FFTs standard
Provides software for PC real-time analysis

Specification:

Bandwidth: 100MHz
Real-time Sample Rate: 1GSa/s
Equivalent Sample Rate: 25GSa/s
Record Length(Sample Points): Single-channel: Maximum 1M; Dual-channel:Maximum 512K (4K,16K,40K optional)
SEC/DIV Range: 4nS/div-40S/div (in a 2, 4, 8 sequence)
Delay Time Accuracy: 500ps
Vertical
- A/D Converter: 8-bit resolution, each channel sampled simultaneously
- VOLTS/DIV Range: 2mV/div~5V/div at input BNC
- Position Range: ±50V(5V/div), ±40V(2V/div~500mV/div), 2V(200mV/div~50mV/div)±400mV(20mV/div~2mV/div)
- Bandwidth Limit: 20MHz
- Rise Time at BNC: ≤3.5ns
- DC Gain Accuracy
  - ±4% for Sample or Average acquisition mode, 5mV/div to 2mV/div
  - ±3% for Sample or Average acquisition mode, 5V/div to 10mV/div
Trigger
- Trigger Sensitivity (Edge Trigger Type)
  - DC : CH1/CH2(Typical) 1div from DC to 10MHz;1.5div from 10MHz to Full
  - EXT(Typical) 200mV from DC to 40MHz
  - EXT/5(Typical) 1V from DC to 40MHz
  - AC: Attenuates signals below 10Hz
  - HF Reject: Attenuates signals above 80kHz
  - LF Reject: Attenuates signals below 150kHz
  - Noise Reject: Reduces trigger sensitivity
- Trigger Level Range
  - CH1, CH2 : ±8 divisions from center of screen
  - EXT : ±1.2V EXT/5 : ±6V
- Trigger Level Accuracy, typical (Accuracy is for signals having rise and fall times ≥20ns)
  - CH1, CH2 : ±(0.3div×V/div) (within ±4 divisions from center of screen)
  - EXT : ±(6% of setting + 40mV)
  - EXT/5 : ±(6% of setting + 200mV)
- Holdoff Range: 100ns-10s
Trigger Type
- Edge: Trigger on the rising or falling edge
- Pulse Width
  - Trigger (when >,<,=,≠) on positive or negative pulses
  - Pulse Width Range: 20ns-10s
- Video
  - Trigger on an NTSC, PAL, or SECAM standard video signal
  - Line Range: 1-525 (NTSC), 1-625 (PAL/SECAM)
- Slope
  - Trigger (when >,<,=,≠) on a positive or negative slope
  - Set Time: 20ns–10s
- Overtime
  - from the rising or falling edge
  - Set Time: 20-10s
- Alternate: Internal trigger on edge, pulse width, video or slope
Measurement
- Cursors
  - Manual : The difference between voltage cursors V, the difference between time cursors T, 1/T calculated by Hz.
  - Tracing : The voltage and time at a waveform point
- Automatic: Pk-Pk, Max, Min, Mean, Cyc RMS, Frequency, Period, Rise Time, Fall Time, Positive Width, Negative Width
Display
- Type: Right angle 7 inch TFT 16-digit color LCD
- Resolution: 800*480 dots
- Contrast: 16 gears, with the progress bar to show adjustment
- Interface: USB host and USB slave
Power Supply
- Voltage
  - 100-120VACRMS(±10%), 45Hz to 440Hz,CAT II
  - 120-240VACRMS(±10%), 45Hz to 66Hz,CAT II
- Power: <30W
- Fuse: 2A, T rating, 250V

Return for refund within: 45 days (details)
Return for replacement within: 6 months (details)

No restocking fee. Shipping charges may apply if returns are not results of FastTech's error.