shopping cart empty
VasDef's Product Reviews
Sort:

Avatar
VasDef
Member

VERIFIED OWNER
  • JoinedFeb 2014
  • Posts 804
  • Reviews 74
  • Kudos245
Overall   (5.0)
› Quality
› Value
PROS
well made
CONS
none
This drip tip tends to work best on devices that have a narrow diameter drip tip hole/fitting. This is great because I have a few atomizers that will not fit some larger tips and this fixes that. This gives someone quite a few options for looks too. That said, it may be quite loose on others so watch out so you don't lose it in a pocket or watch it go flying off. I didn't list this as a con, because it doesn't affect the function of the tip and it works well on most atomizers. Just know what you are getting.
Reviewed on Was this review helpful to you? Yes / No
Mutation X V2 Styled Rebuildable Dripping Atomizer
Mutation X V2 Styled Rebuildable Dripping Atomizer

Avatar
VasDef
Member

VERIFIED OWNER
  • JoinedFeb 2014
  • Posts 804
  • Reviews 74
  • Kudos245
Overall   (5.0)
› Quality
› Value
PROS
Finish is excellent. Air flow adjustment works as it should. Little delrin drip tip was a nice addition Dual coils INCLUDED
CONS
Airflow not for "small cloud" builds...needs good low ohm coil build (.5 and below?) to really work well. Airflow adjuster "wings" have SHARP edges so watch out.
Some people don't like the hex screws. I am fine with them, but be aware that's what this comes with. The airflow on this atomizer seems to perform best with low (sub) ohm builds. I found it a bit too airy for anything over 1 ohm. If that's your thing then have a go. Its well made and looks great. The coils it came with measured at .5 ohms. I used them on my TOBH Atty. Probably would be better on this. I am using a ribbon coil mixed with a kanthal coil for combined ohm rating of .74. I don't recommend that set up for this atomizer and I will be putting it back on .5 duals.
Reviewed on Was this review helpful to you? Yes / No
510 Finned Heat Sink for Atomizers
510 Finned Heat Sink for Atomizers

Avatar
VasDef
Member

VERIFIED OWNER
  • JoinedFeb 2014
  • Posts 804
  • Reviews 74
  • Kudos245
Overall   (5.0)
› Quality
› Value
PROS
Adjustable copper contact screws on top and bottom. Good threading Looks cool. Seems to aid in cooling?
CONS
none
There have been many discussions on these as it seems there was a "bad batch" early on. Mine came in fine with no issues to report. As of now, the early reports of problems seem to be over so I'd recommend one. I liked it so much, I'm buying the three pack with the steel/brass/copper
Reviewed on Was this review helpful to you? Yes / No
Stainless Steel + Copper 510 Drip Tip
Stainless Steel + Copper 510 Drip Tip

Avatar
VasDef
Member

VERIFIED OWNER
  • JoinedFeb 2014
  • Posts 804
  • Reviews 74
  • Kudos245
Overall   (5.0)
› Quality
› Value
PROS
Looks great. Appears well made. Double O-rings
CONS
Mine had a nick on the copper ring. Damaged during shipping?
The copper ring was a bit scratched. Its such a small and cheap item I didn't bother sending it back , but it was still annoying, though not that noticeable. This is doubtless thanks to Fasttech's infamous shipping team. Other than that ...it does what it should and has a nice look and feel.
Reviewed on Was this review helpful to you? Yes / No

Avatar
VasDef
Member

VERIFIED OWNER
  • JoinedFeb 2014
  • Posts 804
  • Reviews 74
  • Kudos245
Overall   (5.0)
› Quality
› Value
PROS
good airflow easy to build on deep well nice look good build quality
CONS
The finish is "tricky". See comments
Being copper, its always going to tarnish a bit and require occasional cleaning to maintain. Also, you need to be wary of certain juices affecting the surface. Again, regular cleaning will be required. Other than that it is a great atomizer and the quality of the clone is quite good. Some cleaning is, of course, required before vaping off it. I recommend a THOROUGH cleaning of both the copper AND the steel elements. I would also recommend cleaning the threads and crews for the wire. Mine had some gunk in them.
Reviewed on Was this review helpful to you? Yes / No