shopping cart empty
bedosus's Product Reviews
Sort:
Pre-Coiled Welded Wires w/ Wicks - NR-R-NR (50-Pack)
Pre-Coiled Welded Wires w/ Wicks - NR-R-NR (50-Pack)

bedosus
Member

VERIFIED OWNER
  • JoinedSep 2013
  • Posts 88
  • Reviews 238
  • Kudos18
Overall   (5.0)
› Quality
› Value
1 of 1 people found the following review helpful
PROS
price
a lot cheaper than buying new coils Average quality, useful for those who do not prepare their own coils. They are very useful for your cartomizer I tried also to use in my Kayfun Some of these did not work well, burnt taste When you have a Kanthal wire and cotton do not have any more problems, but this is a way to go in time
Reviewed on Was this review helpful to you? Yes / No

bedosus
Member

VERIFIED OWNER
  • JoinedSep 2013
  • Posts 88
  • Reviews 238
  • Kudos18
Overall   (5.0)
› Quality
› Value
1 of 1 people found the following review helpful
PROS
Very useful
Very useful is a real power bank if you put the right batteries I put in this 4 Batteries 18650 Panasonic "3400mAh" I do not know if I'll use this to charge my batteries I load only with my Nitecore I4 Now I have a good supply for my smartphone and my e cig, The only problem to use my e cig,. that it turns off if not have a power consumption, In this way i have always turn this and wait for the power bank starts operation I think I will add this little “LED lamp 0.2W USB USB Powered SKU: 1710500 “ so maybe I should not always turn on this. Below you can find a translation of the manual- Thank you to iron_potato who have found and translated this. my KUDOS [Translated from Taobao web as close as I can] Installation: 1. Unscrew two screws & uncover. 2. Put in one to four standard non-protected 18650 batteries with Negative onto spring end. 3. Activate the unit by either:- 3.1 Push button once, underneath the right hand side of the 7 segment display. 3.2 By charging the unit. Note: Need to re-activate on every battery change 4. Put on cover & fasten screws. 5. The display will show the charge percentage with last digit blinking. 6. Strongly recommended to charge it to max on every battery change to have more accuracy on power percentage.("100" shown without last digit blinking) Adjustments & functions: 1. Press power button once, triple "ON" blinks and the unit is switched on. 2. Long press will either show "uP" or "dP" depending on last adjustment state. 3. Press & release power button will adjust the voltage output up or down in 0.5V per press & release. 4. Unit have last voltage setting memory after unit is switched off. 5. All ports can be use with 5.0-5.5V range, with 6.0V & above, both USB ports will be off. 6. Unit will auto off after 20secs with less than 120mA load or manually power off by long press till "OFF" shown. 7. Voltage adjustment will be locked with 4mm port on load & voltage set at 6.0V & above.
Reviewed on Was this review helpful to you? Yes / No
510 to eGo Adapter Convertor
510 to eGo Adapter Convertor

bedosus
Member

VERIFIED OWNER
  • JoinedSep 2013
  • Posts 88
  • Reviews 238
  • Kudos18
Overall   (3.5)
› Quality
› Value
1 of 1 people found the following review helpful
PROS
Only ok for the price
CONS
built with a metal too soft
These are useful and indispensable I read the other reviews everyone is happy and satisfied, has anyone used these only for a short time ? Or maybe I received the ones with the metal more softer ? I bought 3 these Adapters and after a short time have consumed themselves the screw threads after some time of use the thread will consume and these Adapters are dancing inside no longer make contact These Adapters consumed even a little 'the thread of my Vamo Sometimes EVOD gets stuck inside, and for the mini protank these Adapters is too short I ordered 5 others Maybe it's better to pay $ 1 more and have these made in stainless steel I think that everyone would buy these made in stainless steel for $ 2.30 and no one cries
Reviewed on Was this review helpful to you? Yes / No

bedosus
Member

VERIFIED OWNER
  • JoinedSep 2013
  • Posts 88
  • Reviews 238
  • Kudos18
Overall   (4.2)
› Quality
› Value
1 of 1 people found the following review helpful
PROS
Ready to use
These are among the first put on sale here Great to get started and to rebuild their coils The Wick are a little too thin, nearly invisible Wires put in boiling water and did a quick dry burn before using them, can replace Vivi Nova and other Recommended for those who must begin to rebuild their coils
Reviewed on Was this review helpful to you? Yes / No
60W Thermo Controlled Precision Soldering Iron
60W Thermo Controlled Precision Soldering Iron

bedosus
Member

VERIFIED OWNER
  • JoinedSep 2013
  • Posts 88
  • Reviews 238
  • Kudos18
Overall   (5.0)
› Quality
› Value
1 of 1 people found the following review helpful
PROS
Value for money Thermostat range: 200℃-450℃ Graduation: 200℃ 250℃ 300℃ 350 ℃ 450℃
CONS
none
I had an old soldering iron not worked well, and I always was wasting my time With this is all easier and faster if you need to do some small soldering sure you go with this SKU 1247202 worth the money that you spent
Reviewed on Was this review helpful to you? Yes / No